V-Tubler 4T
V-Tubler 4T

V-Tubler 4T

Stok mevcut değil
P/N
CL-W019-OS00TR-A
12,90 € (included VAT)

Özel PC su soğutma konfigürasyonları için V-Tubler 4T 200cm ID 1/2”(13 mm) OD 3/4” (19 mm) esnek tüp.

Thermaltake Esnek Boru V Tüpü 4T 1/2’’ (13 mm)

Thermaltake, özel PC su soğutma konfigürasyonları için V-Tubler 4T su borusunu sunar. Tıbbi sınıf PVC malzemeden üretilen V-Tubler, bükülmeye ve çökmeye karşı dirençlidir, soğutma hatalarına veya sistem performansında düşüşe neden olabilecek bükülme olmadan daha sıkı kıvrımlara izin verir. 1/2”dikenler ve sıkıştırma bağlantı parçalarıyla kullanılmak üzere tasarlanmıştır, kullanıcılara daha iyi montaj, kolay montaj ve ideal akış sağlar. Şunlardan birini seçin: Sisteminizi Thermaltake V-Tubler su borusu ile herkesin görebileceği bir vitrin yapmak için ID 1/2”veya 3/8”.

Tt LCS Sertifikası

Tt LCS Sertifikası, gerçek bir LCS kasasının sahip olması gereken tasarım ve donanım standartlarından geçen,uygun ürünlere verilen ve sadece Thermaltake’e özel bir sertifikadır. Tt LCS sertifikasyonu, Thermaltake kasalarını kullanan tüm ileri seviye kullanıcıların, aşırı sıvı soğutma konfigürasyonlarında bile en uygun kurulumu yapabilmeleri ve en iyi performansı alabilmelerini sağlamak amacıyla yaratılmıştır.

Tıbbi Kalitede Materyal

Tayvan'da üretilen V-Tubler 3T, güvenilir, toksik olmayan ve madde içermeyen tıbbi sınıf PVC'den üretilmiştir. Pürüzsüz iç duvarlar kapalı ilmek sıhhi tesisatını iyileştirerek, boru cidarı üzerinde belirli toplama / tutma işlemlerini azaltır. Çalışma sıcaklığı -4 ℉ (-20 ℃) ile 140 ℉ (60 ℃) aralığındadır.
- İç çap: 1/2” (13 mm)
- Dış çap: 3/4” (19 mm)
V-Tubler 4T'nin malzemesi aşağıdaki gibidir:

Olağanüstü genişleme

1/2” dikenler ve sıkıştırma bağlantı parçaları ile kullanılmak üzere tasarlanan V-Tubler 4T, önceden kesilmiş 200cm uzunluğundaki perakende satış bobinidir. Meraklıların, radyatörleri her bir özel bileşene modüler yükseltmeler yapması ve harici olarak birleştirerek estetik açıdan üstün su soğutma sistemleri oluşturmasını sağlar.

Cautions

Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks

  • To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
  • Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
  • It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
  • Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.

Thermaltake recommends the following steps to be taken after completing your water loop setup

  • It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
  • Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
  • DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
  • Fill the reservoir to the top as it will prevent air from going into the pump
  • If necessary tilt the system slightly from side to side to bleed the air out of the loop.
  • Place some paper towels under fittings and joining points to test for leaks.
  • Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
  • Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
  • Coolant might fade over time.
Daha Fazla Bilgi
P/N CL-W019-OS00TR-A
Malzeme PVC
Renk Şeffaf