Water 3.0 360 ARGB Sync Water 3.0 360 ARGB Sync Water 3.0 360 ARGB Sync Water 3.0 360 ARGB Sync Water 3.0 360 ARGB Sync Water 3.0 360 ARGB Sync Water 3.0 360 ARGB Sync
Water 3.0 360 ARGB Sync

Water 3.0 360 ARGB Sync

Stok mevcut değil
P/N
CL-W234-PL12SW-A
221,90 € (included VAT)

5V RGB özellikli anakartları destekleyen PWM fanlı hepsi bir arada 360 mm sıvı soğutucu.

Sync with Motherboard RGB Software

Designed to synchronize with ASUS Aura Sync, GIGABYTE RGB Fusion, MSI Mystic Light Sync, and ASRock Polychrome. It supports motherboards with a 5V addressable RGB header, allowing you to control the lights directly from the software mentioned above without installing any extra lighting software or controllers. For more details, please visit ASUS, GIGABYTE, MSI, and ASRock official websites.

Category Caution
Chassis, ARGB Fan, ARGB AIO
  • The motherboard signal connector only supports a 5V header.
  • Make sure your motherboard software is the latest version.
RGB Memory, VGA Waterblock, Distro Plate
  • This product can only be used with either the TT RGB PLUS software or the dedicated Motherboard software. By having more than two applications open may cause conflicts
  • The motherboard signal connector only supports a 5V header.
  • Make sure your motherboard software is the latest version.

Cautions

Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks

  • To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
  • Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
  • It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
  • Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.

Thermaltake recommends the following steps to be taken after completing your water loop setup

  • It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
  • Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
  • DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
  • Fill the reservoir to the top as it will prevent air from going into the pump
  • If necessary tilt the system slightly from side to side to bleed the air out of the loop.
  • Place some paper towels under fittings and joining points to test for leaks.
  • Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
  • Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
  • Coolant might fade over time.
Daha Fazla Bilgi
P/N CL-W234-PL12SW-A
Ağırlık 2250 g
Pompa Motor Hızı: 3600 RPM
Anma gerilimi: 12 V & 5V
Güç Girişi: 12V – 3.9 W , 5V – 1.06 W
Su Bloğu Malzeme: Bakır
Fan Boyut:120 x 120 x 25 mm
Hız:PWM 500~1500 R.P.M (2510-4PIN)
Gürültü Seviyesi:25.8 dB-A
Anma Akımı: 12 V & 5V
Güç girişi: 12V- 1.44 W, 5V – 1.6W (tek fan)
Maks. Hava Akımı:56.45 CFM
Maks. Basınç:1.59 mm-H2O
LED Control: ARGB controller or 5V addressable RGB header on motherboard
Tüp Uzunluk: 400 mm
Malzeme: Kauçuk
Radyatör Boyut: 394 x 120 x 27 mm
Uyumluluk Intel
LGA 2066/20113/2011/1366/1156/1155/1151/1150
AMD
TR4/AM4/FM2/FM1/AM3+/AM3/AM2+/AM2
*AMD Threadripper İşlemci kutusunun içerisinde AIO Soğutucu braketi mevcuttur.

User Manual

  • Dosya Adı
  • Açıklama
  • Boyut
  • Version
  • Release Date