Thermaltake Water 3.0 Performer C with Low noise Cable (LNC)
Çok yüksek CPU sıcaklıklarını kontrol altına alabilmek için yüksek verimli bir sıvı soğutucu seçen bilgisayar meraklıları kolay, temiz ve az bakım gerektiren bir kurulum ister. Yeni Thermaltake All-In-One LCS Water 3.0 Series, kullanıcı beklentilerinin ötesine geçecek şekilde tasarlanmıştır. Tek bir basit yükseltme ile daha iyi soğutma performansının ve daha fazla CPU korumasının tadını çıkarın. Ek olarak, düşük gürültülü kablo, düşük hız ve sessiz çalışma için optimize edilmiştir
* Sadece Çin
Yüksek Performanslı Su Bloğu
Tam bakır taban plakası, kasanın hava akışını iyileştirirken, ısı iletkenliğini de maksimuma çıkarır.
Yüksek Verimli Radyatör
Ek ısı dağıtımı için 120 mm'lik bir fan ile desteklenen özel olarak tasarlanmış 120 mm geniş yüzeyli radyatör.
Güçlü Soğutma Fanı
Otomatik olarak ayarlanabilen 120 mm PWM Fan, 2000RPM'ye kadar hız ile soğutma performansını ve sessizliği en üst düzeye çıkarır, herhangi bir aşırı ısınma olasılığını en aza indirir. LNC (Düşük Gürültülü Kablo) gürültü seviyesini 39,9dBA'dan 21dBA'ya kadar, %47 oranında düşürebilir.
*LNC (Düşük Gürültülü Kablo)
Yüksek Güvenilirlikli Pompa
Yüksek kaliteli, güvenilir pompa maksimum su sirkülasyonu sağlar ve bakır plakayı sürekli olarak soğuk tutar.
Evrensel Soket Uyumluluğu
Water 3.0 Performer C, Intel Socket LGA 2011/1366/1156/1155/1150 dahil olmak üzere çoğu Intel ve AMD soketini destekler. Geniş bir AMD platform yelpazesiyle evrensel olarak uyumludur.
Cautions
Thermaltake recommends the following steps to be taken
before using
the
Pacific series radiators and water blocks
- To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
- Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
- It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
- Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.
Thermaltake recommends the following steps to be taken after completing your water loop
setup
- It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
- Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
- DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
- Fill the reservoir to the top as it will prevent air from going into the pump
- If necessary tilt the system slightly from side to side to bleed the air out of the loop.
- Place some paper towels under fittings and joining points to test for leaks.
- Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
- Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
- Coolant might fade over time.
P/N | CLW0222-B |
---|---|
Ağırlık | 750 g |
Pompa | Motor Hızı : 2900 ±150 R.P.M Anma Gerilimi : 12 V Anma Akımı : 175 mA |
Su Bloğu | Malzeme: Bakır |
Fan | Boyut : 120 x 120 x 25 mm Hız : 1200~2000 RPM Gürültü Seviyesi : 27.36 dB-A(MAX) Anma Gerilimi : 12 V Anma Akımı : 0.5 A Maks. Hava Akımı : 81.32 CFM Konnektör : 4 pin |
Tüp | Uzunluk : 300mm Malzeme: Kauçuk |
Radyatör | Boyut : 151 x 120 x 27 mm Malzeme: Alüminyum |
Uyumluluk | Intel LGA 2066/2011-3/2011/1366/1156/1200/1156/1155/1151/1150/775 AMD AM4/FM2/FM1/AM3+/AM3/AM2+/AM2 |